Tools

- Spider removal tool is compatible with all e*thirteen cranks that have a removable spider, and can also be used as an installation/removal tool for e*thirteen bottom brackets

Zipp's shop-level tool is for use with Zipp custom 5.2mm internal nipples. There are two driver lengths: 55mm and 150mm.

- Kit includes tape, 2 valves & 1 valve core wrench

- Bearing extractors set for pushing out 22mm, 24mm, and 30mm ID sealed bearings from bottom bracket cups. - Compatible with Wheels Mfg. 1/2" threaded rod press and handles (PRESS-7 and PRESS-7-PRO). BB-EXT Includes (1) 30mm ID sealed bearing extractor (1) 24mm ID sealed bearing extractor (1) 22mm ID sealed bearing extractor (1) 52mm receiver cup (1) 44mm receiver cup sleeve (1) 42mm receiver cup sleeve (1) 39mm receiver cup sleeve (1) bearing pusher shaft

This 7-piece adapter set is used to install 22mm and larger inside diameter sealed bearings into bottom brackets. Includes adapters for the most common bottom bracket bearings for Shimano outboard cup BBs (HollowTech II), SRAM GXP, Truvativ, FSA, PF30 and BB30 bottom bracket bearings. - Includes open bore drifts for 6805, 24x37, BB30, PressFit30, GXP and BB86 bearings - 10mm ID hole, for use with Wheels Manufacturing bearing press handles - Compatible with Wheels Mfg. PRESS-1 or PRESS-4 handles

Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red

Easy-to-use tool removes and installs replacement bushings in suspension and shock pivots. Includes retaining tool, top cap, and three sizes of bushing drifts. - Fits eyelet sizes - 10mm, 12mm, and 1/2" - Machined aluminum - Anodized Red

This Wheels Mfg. Double End Bottom Bracket wrench fits 16-notch bearing cups with an outside diameter of 44mm as well as 16-notch bearing cups with an outside diameter of 48.5mm. - Machined aluminum - Anodized red. - Compatible with all current Wheels Mfg bottom brackets with notched cups

The dropout saver system is an alternative to replacing badly bent or damaged derailleur dropouts. Rather than replacing the damaged dropout completely, simply drill out the damaged threads, install a dropout saver, and realign the dropout. Kit includes: - (1) 15/32-inch reduced shank drill bit - (2) DS-1 wide dropout savers     - (3) DS-2 narrow dropout savers    

An indispensable tool for the serious amateur bike mechanic or smaller bike shop, the Wheels Manufacturing Bearing Press is designed for installation of bottom brackets or sealed bearings with a minimum I.D. of 10mm. - Package includes 2 handles and a 3/8"-12 threaded rod - Economy Bearing Press, used with separately-purchased bearing adaptors

This Wheels Mfg. GXP-LEFT open bore adapter is used to press 22x37 sealed bearings in to SRAM GXP bottom bracket cups and direct fit frames like TREK BB90. The adapter is machined with one step at 22mm OD, which fits in to the center of the sealed bearing. - Installs: 22X37 (GXP) bearing - Inner Step Outer Diameter: 22mm - Outer Diameter: 37mm - Thru Hole Diameter: 0.387" (9.8mm) - Inner hole sized to fit 3/8" ACME threaded rod - Compatible with PRESS-1 or PRESS-4 handles - Machined, red anodized aluminum - Sold individually

- Headset drift for sealed bearing installation press - Drift is machined with steps to press in headset cups that use either 1-1/8" or 1-1/2" bearings, but may be used for other cups with odd-sized sealed bearings - Compatible with bearing presses using 1/2" diameter rod, such as Wheels Mfg Headset Cup Press (PRESS-8)

Wheels Mfg Headset Cup Press is a robust, and easy to use tool made up of two machined aluminum handles, 1/2" threaded rod, and two machined aluminum drifts. One drift is machined with multiple steps to fit common head tube inner diameters. The other drift is two-sided to press in cups with either 1-1/8" or 1-1/2" bearings, but may be used for other cups with odd sized sealed bearings. - Machined aluminum handles and drifts - Red anodized drifts and handles - Zinc-plated 1/2" diameter threaded rod - Long threaded rod works with long head tubes up to 250mm - Includes one Head Tube Drift - Includes one Headset Cup Drift - Laser etched for easy identification - Made in the USA

Headset drift for sealed bearing installation press. - Drift is machined with multiple steps to fit common head tube inner diameters - Compatible with bearing presses using 1/2" diameter rod, such as the Wheels Mfg. Headset Cup Press (PRESS-8) - Fits the following headtube inner diameters: 34mm, 44mm, 49mm, and 56mm

This 23-piece Wheels Mfg. drift set is used to install 10mm and larger inside diameter sealed bearings, using a press with 3/8" diameter rod - Includes open bore and over axle drifts for 6802, 6901, 6902, 6903, 6000, and 6001 bearings - 10mm ID hole, for use with Wheels Manufacturing PRESS-1 or PRESS-4 bearing press handles

Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

- Works in conjunction with Wheels Mfg sealed bearing press (BTI #WZ-9991) to install 10mm ID and larger bearings into hubs with shouldered axles, always pressing simultaneously on both the inner and outer race of the bearing and preventing damage during the installation process - Includes adapters for 12 different bearing sizes ranging from 10mm to 20mm: 6900,6000 (10mm ID); 6901,6001 (12mm ID); 6802,6902,6002 (15mm ID); 6803,6903,6003 (17mm ID); 6804,6904 (20mm ID) - Made in the USA

Replacement rod for Wheels Mfg. large sealed bearing press (PRESS-1 ) and economy bearing press (PRESS-4 ). Primarily designed for pressing bearings into hubs. - 3/8" x 12TPI threaded rod - 8.75-inch length - One end is drilled and tapped for M5x12mm flat head screw to secure fixed-end handle to rod - Does not include screw (can re-use existing screw)   - This is NOT a replacement for Wheels Mfg. universal bottom bracket press (PRESS-7 )

Replacement handle assembly for Wheels Mfg. large sealed bearing press (PRESS-1). Primarily designed for pressing bearings into hubs. Note: rod diameter is smaller than the hole size in Wheels Mfg. universal bottom bracket drift. Includes: - Machined fixed end aluminum "T" handle with brass insert - Machined non-fixed end aluminum "T" handle with brass insert - 3/8" x 12TPI threaded rod - M5x12mm flat head screw to secure fixed-end handle to rod

Professional, shop-quality, version of the Wheels Mfg Universal Bottom Bracket Press, but with larger handles and brass inserts in the handle faces. Easy to use, this tool is made up of two machined aluminum handles, 1/2" threaded rod, and two machined aluminum drifts. Each drift is machined with multiple steps to fit common bottom bracket shell and bearing diameters listed below. No more searching for the correct size drifts and parts. Just match up the drift to your frame's BB shell size and your bottom bracket's bearing size and press. 1/2" diameter threaded rod resists bending, allowing for the cups to align and press in straight. Drifts can also be used as a frame bottom bracket shell sizing guide! - Machined aluminum handles and drifts - Brass inserts in the tool faces allow each handle to turn freely against drifts - Red anodized drifts and handles - Steps on drift are marked with diameter sizes - Zinc-plated 1/2" diameter threaded rod - Works with BB shells up to 132mm wide Fits: - BB30 (42mm) - PF30 (46mm) - BB86, BB92 (41mm) - BBRight (46mm) - BB386EVO (46mm) - Cannondale BB30A (42mm) - Cannondale PF30A (46mm) - Specialized Carbon OSBB (46mm) - Specialized Alloy OSBB (42mm) - TREK BB90, BB95 (37mm) - PF24 (41mm) - 22/24/30mm inner bearing diameters

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6000 - 6200 - 6800 - 6900

Wheels Manufacturing Sealed Bearing Extractor - 12mm Fits the following bearings: - 6001 - 6801 - 6901

Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268

Wheels Manufacturing Sealed Bearing Extractor - 17mm Fits the following bearings: - 6003 - 6803 - 6903 - 17287

Wheels Manufacturing Sealed Bearing Extractor - 10mm Fits the following bearings: - 6704 - 6804 - 6904

Wheels Manufacturing Sealed Bearing Extractor for GXP (22mm) bearings Fits: SRAM GPX bottom bracket bearings and other bearings with an inside diameter of 22mm

Wheels Manufacturing Sealed Bearing Extractor for 24 x 37mm bearings Fits: - 2437 (Shimano Hollowtech II-compatible outboard bottom bracket bearings) - Other bearings with an inside diameter of 24mm

Wheels Manufacturing Sealed Bearing Extractor - 25mm Fits: - 6805 - Other bearings with inside diameter of 25mm

Wheels Manufacturing Sealed Bearing Extractor - 30mm Fits: - 6806 - Other bearings with an inside diameter of 30mm